|
MBD-X7DB8+-O |
- X7DB8+ (Standard Retail Pack)
|
MBD-X7DB8+-B |
|
|
|
Form Factor |
|
Dimensions |
- 13.68" x 13" (34.7cm x 33cm)
|
|
|
CPU |
- Dual 771-pin LGA Sockets
- Supports up to two Intel® 64-bit Xeon® processor(s) of the same
type below:
- Quad-Core Intel®
Xeon®Processor 5400/5300 sequence (Harpertown /Clovertown processor) up to 3.16 GHz
- Dual-Core Intel®
Xeon®Processor 5200/5100/5000 sequence (Wolfdale /Woodcrest/Dempsey processor) up to 3.40 GHz
- NOTE: Motherboard PCB revision 2.0 or above is required to support Xeon® 5100 (Woodcrest) processors
|
System Bus |
- 1333 / 1066 / 667 MHz system bus
|
Operating System Software |
- Supports 64-bit Operating Systems
- Supports 32-bit Operating Systems
|
|
|
Memory Capacity |
- Sixteen 240-pin DIMM sockets
- Supports up to 64 GB 667 / 533MHz DDR2 ECC FB-DIMM memory
- Dual branch memory bus
- Memory must be populated in pairs
- Memory Mirroring supported
|
Memory Type |
- 667 / 533MHz FB-DIMM (Fully Buffered DIMM) ECC DDR2 SDRAM 72-bit, 240-pin gold-plated DIMMs
|
DIMM Sizes |
|
Memory Voltage |
|
Error Detection |
- Corrects single-bit errors
- Detects double-bit errors (using ECC memory)
- Supports Intel® x4 and x8 Single Device Data Correction (SDDC)
|
|
|
Chipset |
- Intel® 5000P (Blackford) chipset
- MCH + PXH + ESB2
|
SCSI |
- Adaptec AIC-7902 Controller
- Dual-Channel Ultra320 SCSI (Host RAID supports up to 4 drives)
- Host RAID 0, 1, & 10 support
|
RAID |
- Support for Zero-Channel RAID
- Optional: (Card not included)
- RAID 0, 1, 5, 10
|
SATA |
- Intel ESB2 SATA 3.0Gbps Controller
- RAID 0, 1, 5, 10 support (Windows Only)
- RAID 0, 1, 10 support (Linux)
|
IPMI |
|
Network Controllers |
- Intel® (ESB2/Gilgal) 82563EB Dual-Port Gigabit Ethernet Controller
- Supports 10BASE-T, 100BASE-TX, and 1000BASE-T, RJ45 output
- Intel® I/OAT support for fast, scaleable, and reliable networking
|
Graphics |
- ATI ES1000 controller with 16 MB of video memory
|
Super I/O |
|
|
|
Serial ATA |
- Six Serial ATA ports
- Six SATA hard drives supported
|
IDE |
- Single EIDE channel supports up to two UDMA IDE devices (IDE-M, IDE-S) including CF(Compact Flash) Card
- Compact Flash (40-pin connector, IDE 1, single channel) slot
- Supports UDMA Mode 5, PIO Mode 4, and ATA/100
|
Floppy |
- 1 Floppy controller; 1.44 MB, 2.88 MB
|
LAN |
|
USB |
- 2x USB rear ports
- 3x USB internal headers
- Total 5 USB 2.0 Compliant / 1.1 Compliant
|
VGA |
|
Keyboard / Mouse |
- PS/2 keyboard and mouse ports
|
Serial Port / Header |
- 1 Fast UART 16550 serial port
- 1 Fast UART 16550 serial header
|
Parallel Port |
- 1 ECP / EEP parallel port
|
|
|
|
|
2U Chassis |
|
3U Chassis |
|
Tower / 4U Rackmount |
|
Important Chassis Notes |
- To ensure system stability, a 700W (minimum) ATX power supply
[4-pin (+12V), 8-pin (+12V) and 24-pin are required]
|
|
|
PCI-Express |
- 2 (x8) PCI-e slots
- 1 (x4) PCI-e (using x8) slot
- 1 SEPC (Supermicro PCI-e Power Connector) slot for 2U active riser cards with a power extension (i.e. CSE-RR2UE-AX)
|
PCI-X |
- 2x 64-bit 133MHz PCI-X (3.3V) slots
- 1x 64-bit 100MHz PCI-X (3.3V) slot
|
|
|
BIOS Type |
- 8Mb Flash EEPROM with Phoenix® BIOS
|
BIOS Features |
- Plug and Play (PnP)
- SMBIOS 2.3
- DMI 2.1
- PCI 2.2
- ACPI 1.0
- USB Keyboard support
- Hardware BIOS Virus protection
|
|
|
Software |
- Optional IPMI (Intelligent Platform Management Interface) 2.0
- SuperDoctor® III
- Watch Dog
- NMI
|
Power Configurations |
- ACPI Power Management
- Main Switch Override Mechanism
- Wake-On-Ring (WOR) header
- Wake-On-LAN (WOL) header
- Power-on mode for AC power recovery
- Internal / External modem remote ring-on
|
|
|
Voltage |
- Monitors for CPU Cores, +3.3V, +5V, +5V Standby, & ±12V
- 5-Phase-switching voltage regulator with auto-sense from 0.8375V-1.60V
|
FAN |
- Total of four 3-pin and four 4-pin fan headers supporting up to 8 fans
- 8x fans with tachometer status monitoring
- Status monitor for speed control
- Status monitor for on/off control
- Low noise fan speed control
- Pulse Width Modulated (PWM) fan connectors
|
Temperature |
- Monitoring for CPU and chassis environment
- CPU thermal trip support
- Thermal Control for 8x fan connectors
- PSU I2C temperature sensing logic
- Thermal Monitor 2 (TM2) support
|
LED |
- CPU / System Overheat LED
|
Other Features |
- Chassis intrusion detection
- Chassis intrusion header
- SDDC Support
|
|
RoHS |
|
Environmental Spec. |
- Operating Temperature: 10°to 35°C (50°to 95°F)
- Non-operating Temperature: -40°to 70°C (-40°to 158°F)
- Operating Relative Humidity: 8% to 90% (non-condensing)
- Non-operating Relative Humidity: 5 to 95% (non-condensing)
|
|
Facebook
Twitter
LinkedIn
Instagram
Call us today on 01283 576162 to talk directly to one of our server specialists
Who we are
Europe's specialist value added distributor of server chassis, server components and server systems.
Server Case is a specialist server chassis distributor based here in the United Kingdom, with an extensive range of 19” rackmount cases built to suit a variety of environments; including remote industrial servers and everything in between. Furthermore, our distribution partnerships have allowed us to develop and deliver Server Barebones and fully configured systems to the vast IT Channel and Enterprise customers.
Latest Blog
Exploring the World of Barebone Servers: A Comprehensive Guide
Posted on: 5th Apr 2024
In the ever-evolving landscape of information technology, businesses are constantly seeking efficient, cost-effective solutions to meet their server needs. One option that has gained popularity in recent years is the barebone server. Offering a customisable, budget-friendly alternative to pre-built servers, barebone servers provide businesses with the flexibility to tailor their hardware to specif... [...] Read more
Latest Video
View more of our reviews, unboxing and installation videos on YouTube.
Business Links
Site Information